Zhongzhen

Cases
Home > Cases > Apollo Seiko-Compatible PAD Tips for a U.S. Power Electronics Manufacturer

Apollo Seiko-Compatible PAD Tips for a U.S. Power Electronics Manufacturer

Views : 17
Update time : 2026-10-27 

Case study — United States · Power electronics · Apollo Seiko externally heated soldering

Project facts Details
Customer A U.S. power-electronics manufacturer on the West Coast (name withheld)
Products Power supply and battery-management module assemblies
Equipment Apollo Seiko externally heated soldering systems (AC110V)
Tips involved Apollo PAD series, 16mm–24mm heavy-duty sizes
Pain point High thermal-load joints, tip availability and cost on large PAD sizes
Outcome Stable heat on heavy joints, qualified heavy-size source, controlled running cost

Customer Background

This manufacturer builds power conversion and battery-management modules — assemblies dominated by large pads, thick component leads, metal terminals and coil connections. Their soldering cells use Apollo Seiko externally heated (AC110V) systems, and the work lives at the heavy end of the tip range rather than the fine-pitch end.

Unlike small electronics, where the risk is bridging a neighbor pad, the risk here is the opposite: a joint with so much copper mass that it pulls heat away from the tip faster than it can be replaced, producing cold or peaked solder even when everything else is set correctly.

The Problem: Heavy Thermal Mass and Heavy-Tip Supply

  1. Temperature collapse on large joints. Pads connected to copper planes, terminals and coils act as heat sinks. Tips that were marginal in size or plating lost temperature on contact, and operators responded by raising set temperature — shortening tip life without fully solving the wetting problem.
  2. Large PAD sizes were the hardest to source. The plant’s consumption concentrated in the 16mm–24mm range, exactly the heavy-duty sizes with the longest and least certain import lead time for genuine consumables.
  3. Cost concentration. Heavy, high-mass tips carry a higher unit price, and at the volumes this line consumed, the monthly consumable spend was significant.

The engineering team did not want a “similar” tip. They wanted a replacement that seated correctly in the external heater, transferred heat identically on heavy joints, and survived aggressive thermal loads.

Requirements

  • Exact fit for Apollo Seiko AC110V externally heated systems across 16/20/24mm PAD sizes
  • High thermal-mass construction that sustains temperature on planes and terminals
  • Heavy iron plating for high-temperature, lead-free and aggressive-flux duty
  • Pre-tinned, ready-to-run tips with dimensional and plating verification
  • A factory able to hold the large sizes in stock and ship reliably

Our Solution

1. Sized to the joint, not the catalog default. We specified the upper PAD sizes for the actual thermal loads — 16PAD06 for medium connector and general assembly, 20PAD07 for large power-module pads, and 24PAD08 for the heaviest terminals. Choosing adequate thermal mass let the line wet heavy joints at controlled temperature instead of forcing heat with a small tip.

2. Material and plating for sustained load. Each PAD tip is built on a high-purity oxygen-free copper core for rapid, stable heat transfer, with iron plating plus a protective coating specified for continuous high-temperature work. Plating in the 100–150 μm class is recommended where tips run above 380°C or face aggressive flux, per our iron plating thickness guide.

3. Verified before shipment. Heavy-duty tips undergo dimensional inspection and pre-tinning verification, with batch traceability maintained so the customer can reconcile any unit back to its production batch.

4. Process guidance alongside the part. Our engineers recommended dwell and temperature settings that rely on stored thermal mass rather than elevated set temperature — the correct way to handle a heat-sink joint, and the way to protect plating life. Sizing thermal mass correctly is one of the core decisions in our automatic soldering tip selection guide.

Results

Metric Outcome
Heavy-joint wetting Stable, fully wetted terminals and planes with no temperature collapse
Operating temperature Brought back to a controlled window instead of overheating
Heavy-size supply 16/20/24mm PAD sizes supplied on a dependable schedule
Emergency freight No more rush orders of large genuine cartridges
Tip life on hot duty Improved with correctly specified heavy plating
Running cost Lower consumable spend on the highest-priced tip sizes

The customer now runs Zhongzhen PAD tips on its heavy-load Apollo Seiko cells as a qualified source, keeping genuine parts available where change control calls for them.

Why It Worked

Heavy joints fail for the opposite reason that fine joints fail: not too much contact area, but too little stored heat. Solving them required both the right mass and the right plating, plus a supplier that actually keeps the large, slow-moving sizes available. The value to the customer was stable first-pass quality on power modules plus a reliable, lower-cost source for the very tip sizes that used to cause supply anxiety.

For more on matching a supplier to automated production, see our guide on how to choose a soldering tip supplier.

Ask About Heavy-Duty PAD Sizes →

Related News
UNIX-Compatible Soldering Tips for a U.S. Consumer Electronics Assembly Plant
UNIX-Compatible Soldering Tips for a U.S. Consumer Electronics Assembly Plant
2026-10-27 
Case study — United States · Consumer electronic……
TSUTSUMI-Compatible TKH Soldering Tips for a U.S. Medical Device Manufacturer
TSUTSUMI-Compatible TKH Soldering Tips for a U.S. Medical Device Manufacturer
2026-10-27 
Case study — United States · Medical device elec……
Weller-Compatible Soldering Tips for a U.S. Automotive Electronics Manufacturer
Weller-Compatible Soldering Tips for a U.S. Automotive Electronics Manufacturer
2026-10-27 
Case study — United States · Automotive electron……
Customized Automatic Soldering Tip Solution for Communication Equipment Manufacturer in the USA
Customized Automatic Soldering Tip Solution for Communication Equipment Manufacturer in the USA
2026-08-11 
Custom Automatic Soldering Tips: Solution for Co……

Have Questions? Let's Talk.

Fill out the form below and we'll get back to you within 24 hours.

No:87408