Selective Soldering Nozzles | Replacement for ERSA & SEHO Systems
Overview
Selective soldering puts solder exactly where a through-hole joint needs it — and the nozzle is the part that decides whether that happens cleanly. It is also the part that wears out first: solder alloy attacks the bore, dross builds up inside the tip, and a nozzle that suits one board is wrong for the next.
Zhongzhen manufactures replacement selective soldering nozzles for ERSA and SEHO systems in three structures — point, drag and multi-hole plates — machined to a drawing, to a physical sample, or to an original part number. If you already have a nozzle that works, we can reproduce it. If you have a board that needs a shape nobody stocks, we can make that too.
Nozzle Structures We Make
Point nozzles — single hole
For individual through-hole pins and small pads. A conical body feeds solder up a defined bore, so the joint is formed by one controlled dip rather than a wave. Typical use: connectors with a few isolated pins, and mixed boards where only a handful of joints need selective soldering.

Conical body and machined seat — the geometry that locates the nozzle in the solder pot.
Drag nozzles — oval slot
A slotted opening dragged along a row of pins in a single pass. Faster than point soldering on dense connector rows, but the slot width has to match the pin pitch: too wide and it bridges, too narrow and it starves the joint.
Multi-hole nozzle plates
A plate with several bores set to the exact pin pattern of one connector, so a single dip solders the whole connector at once. These are always made to drawing, because the hole pattern is defined by the component footprint rather than by a catalogue.

Four-hole plate — bore spacing follows the connector footprint, not a standard.
Technical Specifications
| Parameter | Specification |
|---|---|
| Product Type | Replacement selective soldering nozzle / nozzle plate |
| Structures | Point (single hole) · Drag (oval slot) · Multi-hole plate |
| Base Interface | B22 / B36 conical base |
| Nozzle Height | 47 mm – 90 mm (standard ERSA height steps) |
| Bore Size | ID / AD made to your drawing or original part number |
| Body Material | Copper alloy with high-temperature oxidation-resistant coating |
| Intended Systems | ERSA VERSAFLOW / ECOSELECT / ECOCELL / SMARTFLOW; SEHO selective soldering systems |
| Manufacturing | CNC machined and dimension-inspected against the approved drawing |
| Customization | Accepted by drawing, physical sample, or original part number |
| Sample Lead Time | 5 – 7 days after drawing approval |
| MOQ | 10 pcs per size (single sample available) |
| Packaging | Protective sleeve + anti-static bag + export carton |
How Custom Manufacturing Works

The base bore and seat are measured from your sample or drawing, then reproduced.
- Send the reference. An original part number, a dimensioned drawing, or a used nozzle — a photo with a ruler alongside is enough to start.
- We return a drawing. Bore ID/AD, overall height, base type and slot or hole pattern, normally within 48 hours.
- Sample approval. A sample is produced for fit and solder testing on your machine before any batch is committed.
- Production. Batch runs from the approved drawing, with dimensional inspection on each lot and batch traceability retained.
Why Buyers Work With Zhongzhen
- Manufactured in our own workshop in Shenzhen — factory-direct pricing, no trading margin
- Copper alloy body with oxidation-resistant coating, using the same base technology as our soldering tips
- Not limited to a fixed catalogue: shape, bore and height are made to your drawing
- Dimensional inspection on every lot, with batch traceability
- Short sample turnaround, so you can test before committing to volume
Compatibility and Trademark Notice
ERSA, SEHO, VERSAFLOW, ECOSELECT, ECOCELL and SMARTFLOW are trademarks of their respective owners. Zhongzhen is an independent manufacturer of aftermarket replacement parts. References to these systems describe the equipment our nozzles are intended to fit and do not imply any affiliation with, endorsement by, or authorisation from the original equipment manufacturers.
Get a Quote
Send us the part number, drawing, or a photo of the nozzle with its dimensions, together with the machine model and the quantity you need. We will reply with a drawing and a quotation. Samples are available before production.



